Most 3d print issues can be traced from the symptom back to a short list of causes: damp filament, a poorly set first layer, a partly blocked nozzle or a loose belt. Name what you see on the failed print, make one fix, then reprint a small test piece before touching anything else.
Quick Answer
Match the symptom to its first check. Strings between parts point to wet plastic or too much heat, lifted corners to bed temperature and draughts, and a missing first layer to bed height. PLA commonly prints near 190 to 220 degrees Celsius, so move temperature in steps of about 5 degrees. A fresh spool costs around R249 to R399, which is cheaper than a week of guessing.
🔍 Read the symptom before you change anything
Look at where the print went wrong, because the location tells you the cause.
Failure at the very start
If the first layer is patchy, see-through or does not stick, the nozzle is usually too high or the plate is dirty. Re-level, wipe the plate with isopropyl alcohol and lower the Z offset in small steps until neighbouring lines fuse.
Failure halfway up
Spaghetti mid-print often means the part came loose from the bed, or the head struck a curled edge. Layers that suddenly shift sideways point to a loose belt or a snagged cable.
Rough or messy surfaces
Strings, blobs and a fuzzy texture usually come from moisture or hot plastic. Pits and gaps between lines suggest under-extrusion, often from a partial clog or a spool that is binding.
💧 Moisture, heat and our weather
Filament absorbs water from the air. In coastal Durban, and in Cape Town during wet winter weeks, a spool left on the printer for a month will start to hiss and pop at the nozzle. Keep spools in a sealed box with a desiccant sachet, and dry a problem spool in a low-heat food dehydrator, following the temperature guidance for that material.
Heat matters in the opposite direction. A garage in a Gauteng winter drops enough to make corners lift, so shelter the machine from draughts and consider a cardboard or fabric cover. Raise the bed temperature by 5 degrees if edges curl.
Temperature steps worth knowing
If a print string-webs, lower the nozzle by 5 degrees and try again. If layers separate or the surface looks dull and weak, go up by 5 degrees instead. Stay inside the range printed on the spool label, and give the hotend a minute to settle after each change.
🛠️ Mechanical checks that fix more than you expect
Run through this list with the printer off:
- Belts: pluck each one. It should twang, not flop.
- Nozzle: after heating, push filament by hand. Resistance or a thin curled strand points to a clog, and a cold pull usually clears it.
- Extruder tension: too tight grinds the plastic, too loose lets it slip.
- Bed screws and springs: a bed that has drifted ruins the first layer.
- Cooling fan: make sure it spins and its duct is not blocked.
Dust is the quiet enemy on the Highveld. A soft brush on the rails and a drop of machine oil, applied sparingly, keep motion smooth. If you outgrow a worn machine, the 3D printers category shows the current options.
🧪 One change at a time
Print a small calibration piece, such as a 20 mm cube or a retraction tower, because it takes minutes and shows the problem clearly. Change one setting, reprint, compare. Writing down each change saves you from chasing your own tail.
When filament itself is suspect, try a fresh spool from the filament range as a control. If the same file prints well on new plastic, the old spool was the cause.
Frequently Asked Questions
What is the first setting to adjust when stringing appears?
Lower the nozzle temperature by 5 degrees, then raise retraction distance slightly. Dry the spool as well, since damp plastic strings no matter what the slicer says.
Why do my prints keep lifting at the corners?
Heat leaves the corners faster than the middle. Clean the plate, add a brim, raise bed temperature slightly and keep draughts away.
How can I tell a clog from a bad extruder?
Heat the nozzle and push filament by hand. If it flows, the extruder is the weak link, and if it resists, the nozzle is partly blocked.
Do I need to level the bed often?
Check after moving the printer, changing the build plate or noticing the first layer change. A stable machine may need it only occasionally.
Is a stuck print a bed problem or a filament problem?
Look at the first layer. If it is squashed and even, suspect the filament or cooling. If it is round and loose, suspect the bed.
Ready to get clean prints again?
Browse Evetech's 3D printing filament and printer categories for fresh spools and machines that match your setup.