Learning how to mount an HP 24f monitor is mostly about matching three things: the VESA hole pattern on the back, the weight limit of the arm or bracket, and the surface it will hold onto. Most 24-inch screens use a 100x100 millimetre pattern, though some use 75x75, so confirm on your own unit before buying anything. With those matched, mounting takes about twenty minutes and a Phillips screwdriver.

Quick Answer

Measure the four screw holes on the back of the monitor, usually 75x75 or 100x100 mm, then buy an arm or wall bracket rated above the monitor's weight. A basic single arm costs roughly R300 to R900. On brick or plaster walls use masonry plugs, and check for hidden cables before you drill. Read your exact model's manual for its hole pattern.

📏 Check VESA, Weight and Screws First

VESA is a standard square of four threaded holes. Measure from the centre of one hole to the next, across and down. Many 24-inch office monitors use 100x100 mm; smaller or thinner ones may use 75x75 mm. Some models hide the holes behind a cover on the stand neck, so remove the stand and look.

Next, read the weight. A 24-inch monitor commonly weighs 3 to 5 kg without its stand, and any arm you choose must list a higher maximum load. Then check the screws. Most 75 and 100 mm patterns use M4 screws, in a length set by how deep the holes are. Use the screws that come in the arm's box and never force one that stiffens, because cross-threading ruins the hole.

🪛 Fitting a Desk Arm

Lay the monitor face-down on a soft towel and remove the stand by loosening its screws or pressing its release clip. Attach the VESA plate to the back with the four M4 screws, tightening in a cross pattern so it sits flat.

Choose the clamp or grommet that suits your desk. A clamp needs a solid edge about 10 to 80 mm thick and no lip or hollow underneath. Thin, glass or hollow tops can crack, so spread the load with a steel plate underneath or use a grommet mount through a cable hole. Slide the arm onto its pole, lock the height, and adjust the gas spring until the monitor stays where you leave it.

If you share a small desk in digs or a res room, an arm frees the whole surface under the screen for a laptop or keyboard. Browse the monitor accessories category for arms and brackets with the right load rating.

🧱 Mounting on a Wall

For a fixed or tilting wall bracket, hold the plate against the wall with a spirit level and mark the holes. Drill with a masonry bit sized to the plug, and use plugs rated for several times the monitor's weight. Plaster over brick hides the real wall, so make the hole deeper than the plaster layer.

Before drilling, run a cable and pipe detector over the area. Wiring in South African homes usually runs vertically from sockets and switches, so avoid drilling straight above or below them. Switch off the circuit at the board if you have any doubt.

Fix the bracket, hang the monitor with both hands, then tighten the safety screw if the bracket has one. Leave cable slack so a tilt does not pull a plug loose. If you are replacing the screen too, compare options in the gaming monitor range, many of which are VESA-ready.

✅ Final Checks

Before you lift the monitor onto the arm, set the arm's tension screw roughly in the middle of its range. A 24-inch panel is light enough that a fully tightened spring will shoot it upward, and a fully loose one will let it sink. Fine-tune once the screen is hanging, using the small hex key that comes in the box. If the arm has a pole, mark the height with a strip of tape so you can return to it after moving the desk.

Give the screen a gentle push to confirm it holds. Set the viewing height so the top edge sits at or just below eye level, and the screen is about an arm's length away. Route cables along the arm with the clips supplied, leaving a loop at each joint so moving the arm never tugs a connector.

Frequently Asked Questions

What is VESA on a monitor?

VESA is a standard square of four screw holes on the back, commonly 75x75 or 100x100 millimetres. The arm must match that pattern and the monitor's weight.

Does every HP monitor have VESA holes?

Not visibly. Some hide them under a cover on the stand neck, so remove the stand and check the manual for your exact model.

What screws does a VESA mount use?

The 75 and 100 mm patterns use M4 screws. Take the length from the arm's box and stop if a screw resists.

Can an arm clamp onto a glass desk?

Not safely without reinforcement. Use a steel plate or a grommet mount, because thin or glass tops can crack under a clamp.

How do I avoid cables in the wall?

Scan the area with a cable detector first, and avoid drilling directly above or below sockets and switches.

Ready to free up your desk space? Browse the monitor accessories category at Evetech to compare arms and brackets, and match one to your screen's VESA pattern and weight.