Sim Racing Upgrade Order: What to Replace on a G923

The Logitech G923 is a useful force-feedback starting point, so its wheelbase does not have to be the first part you replace. Braking consistency and mounting usually show their limits sooner. Upgrade pedals where platform support allows, secure the rig, then decide whether a new wheelbase would add enough detail to justify a new ecosystem.

Quick Answer

On PC, shortlist a supported load-cell pedal set that can connect through its approved USB path, then hard-mount it. On console, confirm whether the pedals connect through the G923 or a manufacturer-approved adaptor for your exact platform. Add a rigid stand or cockpit before increasing brake force. Replace the wheelbase last unless it has a fault, lacks game support or clips through the feedback you need.

Step 1: prove the current limitation

Drive a familiar car and record ten clean laps. Look at lap spread and brake traces where the sim provides them. If braking points and release pressure vary while steering remains controlled, the pedals are the strongest candidate.

Check physical movement. Watch the pedal base, chair and desk during a heavy stop. A new sensor cannot help when the whole seating relationship changes.

Set G923 force feedback below clipping before judging it. Excess force can turn separate effects into one heavy signal and make the wheelbase feel less detailed than it is.

Step 2: choose a pedal route by platform

PC users can often mix a supported USB pedal set with the G923 wheel, provided the game accepts separate devices. Console users face a tighter path because accessories may need to connect through the wheelbase.

Verify the exact pedal, adaptor and console combination in Logitech or the pedal maker's current support material. Do not infer compatibility from a plug shape. A load-cell pedal advertised for PC may have no direct console path.

The sim-racing range offers a place to compare current pedal and mounting options. Open the model page and manual. The grid itself does not prove it pairs with the G923.

Step 3: mount before calibrating force

A load-cell brake measures pressure, so it can require far more push than the stock travel-based pedal. Bolt the base to a supported pedal plate. Secure the chair to the stand or use a cockpit with fixed seat rails.

Set the pedal distance so your knee remains bent at full force. Adjust the brake to a pressure you can reach without pulling on the wheel. Start lower and build only if the body and frame remain stable.

Calibrate minimum and maximum input in the pedal software and game. Add a small dead zone only when the sensor or resting foot creates unwanted input.

Step 4: improve mounting around the G923

The G923 can clamp to a desk, but a wheel stand improves position and keeps pedals connected to the steering mount. Check wheel-deck holes, pedal pattern and chair link.

A full cockpit makes sense when the room has a permanent footprint or the new brake overwhelms a folding stand. Choose one with a future wheelbase mounting route. Do not buy a light frame that must be replaced with the base.

Step 5: decide whether the wheelbase is ready to go

After pedals and mounting settle, retest the same laps. Upgrade the wheelbase when force clips at useful settings, steering response feels coarse, noise disrupts the room or you need rims and controls the G923 cannot offer.

Moving to direct drive may replace the wheelbase, rim, clamp and console compatibility path. Price the entire ecosystem. Keep the G923 as a complete set for another setup or pass it on with all original parts rather than splitting a working bundle without a plan.

Keep the original pedal set and cables until the new path has completed several stable sessions. That gives you a known-good control for diagnosis if the game loses an axis after an update.

Step 6: delay low-impact extras

A shifter is useful for manual cars. It does not improve formula or paddle-shift braking. A handbrake suits rally and drift. A button box helps only after the wheel buttons run out.

Spend on these after the control problem is solved. A new rim cover and lighting change appearance while the same pedal movement remains.

The flight-simulator gear page matters when one stand carries several control systems. Plan USB ports and quick-removal mounts before fixing the pedal plate in a position that blocks rudder-pedal use.

Frequently Asked Questions

Can any load-cell pedals plug into a G923?

No. Connection depends on the pedal, platform, game and any manufacturer-approved adaptor. Verify the exact chain.

Should I replace the G923 wheelbase first?

Keep it while force feedback is usable and braking or mounting is the larger inconsistency.

Do load-cell pedals require a cockpit?

They require stable pedal and seating mounts. A suitable wheel stand with chair restraint may be enough.